Free DIY Furniture Plans // How to Build a Rocking Chair

Nothing says spring like a rocking chair on the porch. I kind of have a thing with chairs that rock... or bounce. I guess I never grew out of that stage from my years as a baby? Who knows, but there is definitely something so soothing about sitting in a rocking chair, listening to the evening sounds. It is even better in the morning, but somehow school routines and young children seem to keep this from happening during the week. A gal can dream though...

As with all of our plans, you are building at your own risk and you should have a firm understanding of building in general before you attempt many of our plans (some are perfect for beginners, others... not so much). With that, go forth, have fun, take lots of pictures and share them in a showcase or on social media with the hashtag #builtTDCtuff and we will share our faves!

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

• Tape Measure
• Saw – Jig Saw, Circular, Table, or Miter Saw
• Drill
• Countersink Drill Bit
• Square
• Sander
• Kreg Jig
• Brad Nailer

• 2 – 1x2 at 8’
• 3 – 1x3 at 8’
• 2 – 1x4 at 8’
• 1 – 1x6 at 8’ (or use 3/4” plywood, ripped down to 5-1/2” wide)

• 1 ¼” Pocket Hole Screws
• 1 ¼” Wood Screws
• 20 - 1/4” 2” long bolts and 1/4" nuts
• 1/4" Spade Bit
• Clamps
• Safety Gear
• Wood filler
• Wood glue
• Sanding Supplies
• Finishing Supplies
• Paste Wax

• 1 – 1x2 at 16” – Backrest Top Frame
• 2 – 1x2 at 18-1/2” – Backrest Side Frames
• 2 – 1x3 at 2-1/2” – Armrest Supports
• 2 – 1x3 at 21” – Backrest Sides
• 5 – 1x4 at 19” – Backrest Slats
• 2 – 1x3 at 23” – Seat Sides
• 2 – 1x2 at 17-1/2” – Seat Front and Seat Back
• 5 – 1x4 at 19” – Seat Slats
• 2 – 1x3 at 22” – Armrests
• 2 – 1x3 at 12-1/4” – Side Frame Tops
• 4 – 1x3 at 24-1/2” – Side Frame Sides
• 2 – 1x2 at 19-1/2” – Side Frame Bottoms
• 2 – 1x6 at 35” – Rockers

Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

/ Click on Images to Enlarge

Cut the pieces for the Backrest Top Frame and Backrest Side Frames. With the Kreg jig set for 3/4” material, drill pocket holes in each end of the Backrest Top Frame. Assemble as shown with glue and 1-1/4” pocket screws.

Cut the pieces for the Armrest Supports, Backrest Sides, and Backrest Slats.

Cut the Armrest Supports as shown.

Chamfer the top back corner of the Backrest Sides at a 45-degree angle, if desired. You can also “round out” the bottoms of the Backrest Sides as shown. Attach the Backrest Sides to the Backrest Side Frame pieces as shown with glue and 1-1/4” wood screws. Attach the Armrest Supports to the Backrest Sides as shown with glue and 1-1/4” wood screws.

Attach the Backrest Slats to the Backrest Top Frame and Backrest Sides as shown with glue and 1-1/4” wood screws.

Cut the pieces for the Seat Sides, Seat Front, and Seat Back. Chamfer the bottom front corner of the Seat Sides at a 45-degree angle, if desired.

With the Kreg jig set for 3/4” material, drill pocket holes in each end of the Seat Front and Seat Back. Assemble as shown with glue and 1-1/4” pocket screws.

Cut the pieces for the Seat Slats. Attach the Seat Slats to the Seat Front, Seat Sides, and Seat Back as shown with glue and 1-1/4” wood screws.

Cut the pieces for the Armrests, Side Frame Tops, Side Frame Sides, and Side Frame Bottoms. You can “round out” the outer corners of the Side Frame Sides as noted to allow for better chair movement. With the Kreg jig set for 3/4” material, drill pocket holes in each end of the Side Frame Tops and Side Frame Bottoms. Next, drill pocket holes in the top end of the Side Frame Sides. Assemble as shown with glue and 1-1/4” pocket screws. Repeat this step for the other side.

Cut the pieces for the Rockers. Draw out the shape as shown and cut out with your jigsaw. Make sure you draw a gentle curve. For this project, we used a radius of 62-1/2” for the Rocker curves. If desired, “round out” the end corners of the Rockers with your jigsaw or sander.

Clamp the Rockers to the Side Frame Sides as shown. Using a 1/4” spade bit, drill holes through both of the clamped pieces. Attach the Rockers to the Side Frames Sides as shown with glue and 1/4” bolts and nuts. Once assembled, you can see what part of the Side Frame Sides extend past the Rockers. Use your jigsaw or sander to remove this excess wood. Repeat this process with the other side.

Lay one of the Side Frame assemblies on the ground or table, with the pocket holes facing up. Lay the Seat assembly on the Side Frame assembly as shown and secure with clamps. Using a 1/4” spade bit, drill holes through both of the clamped pieces. Attach the Side Frame Sides to the Seat Side as shown with glue and 1/4” bolts and nuts. Repeat this process with the second Side Frame assembly.

Set the Rocking Chair upright. Using clamps, position the Backrest assembly to the Side Frame assemblies as shown. The bottom corner of the Armrest should be flush with the back edge of the Backrest Side and should be set directly on the Armrest Support. Use your 1/4” spade bit to drill through both the clamped pieces where noted. Attach the Side Frame Sides to the Backrest Side as shown with glue and 1/4” bolts and nuts. Repeat this process with the other side.

Just sit back, relax, and rock your worries away!

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

// Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you ONLY use 1 image and provide an ADEQUATE link back to the original source and appropriate plan! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential. By accessing or using any part of the web site, you agree to become bound by the terms and conditions of this website as outlined under Terms of Use. If you do not agree to all the terms and conditions of this agreement, then you may not access the Website or use any services. The information contained in this website is for general information purposes only. The information is provided by The Design Confidential.com and while we endeavor to keep the information up to date and correct, we make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the website or the information, products, services, or related graphics contained on the website for any purpose. Any reliance you place on such information is therefore strictly at your own risk. In no event will we be liable for any loss or damage including without limitation, indirect or consequential loss or damage, personal injury or death, or any loss or damage whatsoever arising from loss of information or profits arising out of, or in connection with, the use of this website. I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it. The Design Confidential.com is inspired by but does not replicate exact designs, any similarities between these plans and items sold at specialty retailers is coincidential and not endorsed by or related to any said retailers. // Post May Contain Affiliate Links