Free DIY Toy Plans // How to Build a Children's Doll Accessory Ballerina Bar

For your little ballerina, an adorable doll sized ballerina bar so your babe and her favorite 18 inch doll can have dance class together. This free plan for an easy to build doll ballerina bar is sure to please this holiday season. As part of our ongoing Handmade Holiday series, this project joins a well rounded group of adorable gifts you can make yourself!

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

• Tape Measure
• Saw – Jig Saw, Circular, Table, or Miter Saw
• Drill
• Countersink Drill Bit
• 1/2" Drill Bit
• Square
• Sander
• Kreg Jig
• Brad Nailer

• 1 - 1x2 at 4’
• 1 - 3/4” plywood at 2’x2'
• 1 – 3/8” dowel at 12”

• Mirror at 9-1/2”x13”
• 1 ¼” Pocket Hole Screws
• 1 ¼” Wood Screws
• Clamps
• Safety Gear
• Edge banding
• Wood filler
• Wood glue
• Sanding Supplies
• Finishing Supplies

Cut the pieces for the Mirror Sides and Mirror Bottom. Set the Kreg jig for 3/4” material and drill pocket holes in the top ends of the Sides and in each end of the Bottom. Place the screws so that a 1/4” rabbeting bit run along the inside of the Mirror will avoid them (see Step 5). Assemble as shown with glue and 1-1/4” pocket screws.

• 2 – 1x2 at 12-1/2” – Mirror Sides
• 1 – 1x2 at 9” – Mirror Bottom
• 1 – 3/4” plywood at 3”x12” – Mirror Top
• 2 – 3/4” plywood at 2”x8-1/2” – Mirror Stands
• 2 – 1x2 at 2” – Bar Holders
• 1 – 3/8” dowel at 9-3/4”– Bar

Cut the piece for the Mirror Top. From each top corner, draw a 1-1/2” radius circle 3” radius circle. Next, measure and mark a 1-1/2” line from the top and side edges. Using your jigsaw, cut out the shape in the diagram. Attach to the Mirror Sides with glue and 1-1/4” pocket screws.

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Cut the pieces for the Mirror Stands. Measure, mark and cut a 1” triangle on each top corner as shown. Using your jigsaw, cut out the shape in the diagram. Attach to the bottom of the Mirror Sides with glue and 1-1/4” wood screws.

Next, measure, mark, and cut a 1/2” triangle on the bottom corner of the Bar Holder as shown. Using your jigsaw, cut out the shape in the diagram.

Cut the pieces for the Bar Holders. Connect each corner with a line to find the center as shown. Drill a 1/2” radius circle on the center of the “x,” approximately 1/4” deep.

Attach one of the Bar Holders to a Mirror Side with glue and 1-1/4” wood screws, screwed in from the back of the Mirror Side. The Bar Holder will be positioned 1/2” from the Mirror Side outer edge and 6-3/4” from the bottom of the Mirror Side as shown.

Cut the piece for the Bar. The Bar will be 9-3/4” long – each end of the Bar dowel will extend into the 1/2” hole drilled into the Bar Holders. Position the second Bar Holder, similar to the first.

Set router bit depth to cut a ¼” rabbet. Cut the rabbet on the inner back of the frame to allow for the mirror. Use a chisel and hammer to square the corners. Adhere the mirror using mirror adhesive or a tab framing gun. The mirror frame can be attached to the vanity with pocket screws through the side frame as well as metal mending plates.

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

// Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you ONLY use 1 image and provide an ADEQUATE link back to the original source and appropriate plan! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential. By accessing or using any part of the web site, you agree to become bound by the terms and conditions of this website as outlined under Terms of Use. If you do not agree to all the terms and conditions of this agreement, then you may not access the Website or use any services. The information contained in this website is for general information purposes only. The information is provided by The Design Confidential.com and while we endeavor to keep the information up to date and correct, we make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the website or the information, products, services, or related graphics contained on the website for any purpose. Any reliance you place on such information is therefore strictly at your own risk. In no event will we be liable for any loss or damage including without limitation, indirect or consequential loss or damage, personal injury or death, or any loss or damage whatsoever arising from loss of information or profits arising out of, or in connection with, the use of this website. I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it. The Design Confidential.com is inspired by but does not replicate exact designs, any similarities between these plans and items sold at specialty retailers is coincidential and not endorsed by or related to any said retailers. // Post May Contain Affiliate Links