Free DIY Furniture Plans // How to Build an Andrew Table

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

This fine looking specimen has quite a bit in common with one of our most loved on project plans, the Indoor / Outdoor Provence Beam Dining Table, but if you notice the fancy schmancy truss setup supporting this table, it is essentially like the Provence on steroids. So my friends, I will go so far as to say that if you have your heart set on the Provence, but you like an element of this new exciting guy, then by all means, build the Provence and add any modification from this set of plans to give it a little extra something. Or just build this table. Whatevs.

• Tape Measure
• Saw – Jig Saw, Circular, Table, or Miter Saw
• Drill
• Countersink Drill Bit
• Square
• Sander
• Kreg Jig
• Brad Nailer

• 1 – 4x4 at 8’
• 20 – 2x4 at 8’

• 2 ½” Pocket Hole Screws
• 2 ½” Wood Screws
• Clamps
• Safety Gear
• Edge banding
• Wood filler
• Wood glue
• Sanding Supplies
• Finishing Supplies

Cut the pieces for the Side Top and Side Bottom (current pieces shown in white for each step).

// Refer to specific steps in this plan before cutting pieces - some pieces are cut with angled ends and their exact measurements may differ from the measurements listed below. Measurements listed below are PRE-BEVEL dimensions and the actual end measurements will change once cut according to specific steps.

• 2 – 2x4 at 35” – Side Top
• 2 – 4x4 at 35” – Side Bottom
• 4 – 2x4 at 25” – Side Outsides
• 4 – 2x4 at 10” – Side Inside A
• 2 – 2x4 at 10-3/4” – Side Inside B
• 2 – 2x4 at 15-3/4” – Side Inside C
• 2 – 2x4 at 27-3/4” – Side Inside D
• 1 – 2x4 at 89” – Center Bottom
• 2 – 2x4 at 7-3/4” – Center Outside A
• 2 – 2x4 at 20-3/4” – Center Outside B
• 1 – 2x4 at 39-3/4” – Center Inside A
• 1 – 2x4 at 27” – Center Inside B
• 1 – 2x4 at 67-1/4” – Center Inside C
• 12 – 2x4 at 96” – Table Top Boards
• 2 – 2x4 at 42” – Table Ends

Next, cut the pieces for the Side Outsides. Set the Kreg jig for 1-1/2” material and drill pocket holes in both ends of each Side Outside piece. For this Table, we have located the pocket holes either facing the inside of the Table or facing the ground. Assemble as shown with glue and 2-1/2” pocket screws.

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

With the Table still upside down, place the assembled Table Center onto the Table Top, between the Table Sides as shown. Center Inside A and Center Inside C will be 8” from the Table Sides and 19-1/4” from the Table Top edges. The Center Bottom will be centered on the Side Bottoms, with 15-3/4” on each side as shown. Assemble as shown with glue and 2-1/2” pocket screws. Flip this fancy table over and admire all those angle cuts!

Cut the pieces for the Side Insides. Using the Kreg jig, drill pocket holes in both ends of each Side Inside piece. Assemble as shown with glue and 2-1/2” pocket screws.

Next, cut the pieces for the Center Outsides. Using the Kreg jig, drill pocket holes in both ends of each Center Outside piece. Assemble as shown with glue and 2-1/2” pocket screws.

Cut the piece for the Center Bottom.

Cut the pieces for the Center Insides. Using the Kreg jig, drill pocket holes in both ends of each Center Inside piece. Assemble as shown with glue and 2-1/2” pocket screws.

Cut the pieces for Table Top Boards and Table Top Ends. Using the Kreg jig, drill pocket holes in both ends of each Table Top Board. To make sure that the Table Top is as flat as possible, drill several pocket holes along the long side of the Table Top Boards as shown below. Assemble as shown with glue and 2-1/2” pocket screws.

(Bottom view)

Lay the assembled Table Top on the ground with its bottom facing up. Next, position the assembled Table Sides on each end of the Table Top as shown below. The Table Sides will be positioned 3-1/2” from both the long and short edges of the Table Top. Attach the Table Sides to the Table Top with 2-1/2” wood screws through the Side Top into the Table Top. Drill pilot holes if necessary.

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

// Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you ONLY use 1 image and provide an ADEQUATE link back to the original source and appropriate plan! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential. By accessing or using any part of the web site, you agree to become bound by the terms and conditions of this website as outlined under Terms of Use. If you do not agree to all the terms and conditions of this agreement, then you may not access the Website or use any services. The information contained in this website is for general information purposes only. The information is provided by The Design Confidential.com and while we endeavor to keep the information up to date and correct, we make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the website or the information, products, services, or related graphics contained on the website for any purpose. Any reliance you place on such information is therefore strictly at your own risk. In no event will we be liable for any loss or damage including without limitation, indirect or consequential loss or damage, personal injury or death, or any loss or damage whatsoever arising from loss of information or profits arising out of, or in connection with, the use of this website. I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it. The Design Confidential.com is inspired by but does not replicate exact designs, any similarities between these plans and items sold at specialty retailers is coincidential and not endorsed by or related to any said retailers. // Post May Contain Affiliate Links