Completed: The Watson Bra & Bikini Set

Hey look! I made another bra! And matching undies!!

I’m loving my Marlborough bras so so much (yes, plural. I actually have two now, but I’ll save #2 for another post – this post is all about Watson), but I was really intrigued by the new Watson Bra pattern from Cloth Habit. Instead of a low movement fabric, this baby is sewn up in a fabric with lots of stretch. The cups are higher and more modest and there is no underwire. What really got my attention was the longline option, as well as the included bikini bottom pattern. SHUT UP AND TAKE MY MONEY!

Since I’m still pretty new to this whole new world of lingerie, I let the pattern hold my hand when choosing a size and following the instructions. I measured to a 30D (to recap, in case there is anyone new here, I usually wear a 28DD), which fits pretty spot-on. Which is good, because other than hold the little cups up to my boobs while I was sewing them – I wasn’t able to actually try the thing on until I was completely finished with it. Talk about a bummer if that hadn’t worked out! Thankfully, the fit is pretty good. One cup has a tiny bit of sideboob action going on – but that breast is also slightly bigger, so I’m at the point now where I’m trying to decide if it’s worth tweaking the fit for a really custom bra. I’m pretty happy with the fit of the band – it’s nice and tight, like I like it, but it’s also very comfortable.

The pattern has you cut the cups and cradle in a stretch fabric, the band in power mesh, and then the cradle is lined with a non-stretch to stabilize. Lining that section was obviously a little difficult for me – and I ended up getting quite a few folds as a result. Wah. For my next make, I am going to try fusing my stabilizer to see if that helps. It’s not the end of the world with these folds – but of course I’m always looking to improve.

The bra includes standard bra hardware – hooks and eyes, adjustable straps, and decorative elastic. I do like that about the pattern, because it makes it look a lot less like some kind of soft training bra that a pre-teen would wear, and more like… a cute bra without underwires, I guess.

Because of the needed stretch fabric, this bra doesn’t require the same sort of fitting that a structured bra would command (such as the Marlborough). It’s very soft and forgiving. The pattern is rated as being pretty easy and a great way to introduce beginners to bra-making. That being said – while I didn’t find the bra necessarily difficult to make, I do think that the Marlborough was easier to sew! Mostly because that lycra was stretching and sliding all over the place, and getting the cups in just so required quite a bit of precision. Still, it only took me a couple of hours to make, so that should count for something.

The instructions are pretty good! I might be biased – because I’ve already made two bras, I have my copy of Demystifying Bra Fitting and Construction

on stand-by, and I’ve had enough bra-making conversations to know at least a little of what I’m talking about – but I found them very easy to follow along with. One part that was missing was determining strap length, but it’s my understanding that the pattern was updated with directions on how to do this (I personally just cut two 18″ straps. Worked perfectly! They are adjustable, after all). There were a few minor parts of the pattern that I changed based on preference – such as trimming the excess fabric before topstitching the elastic to the wrong side – but what’s included with the pattern is great as-is. There’s a lot of helpful info for choosing fabrics and trims, and tips for stitch settings when choosing your zigzag stitch. Also, there is currently an entire Watson Bra sewalong happening at Cloth Habit right now, so there’s that if you need even MORE hand-holding!

Here’s an inside shot. As you can see, I did not finish my seams – just left ‘em raw. It seems to work fine for my other bras, anyway. In the future, I’d love to learn how to properly finish my seams – or even line the whole thing – but I really want to nail down fit and technique before I start going too far down the deep end.

Rather than try to source all the materials and notions myself, I decided to splurge on a Watson kit from Blackbird Fabrics. The kit includes everything you need – 4 way stretch lycra, matching powermesh, elastics and trims, metal strap rings and sliders (stupidly, that was my favorite part haha. THEY LOOK SO GOOD), even the aforementioned cradle stabilizer and cotton knit for the crotch lining (for the undies, obviously). There’s enough in the kit to make both the bra and the matching bikini, and you can choose if you want a kit for the standard band or the longline. Since my boobs run on the small side, I’d reckon I could probably make 2 or even 3 bras with how much fabric I have left over (and maybe even a little bit of trim!). This color set is sapphire blue with black trims – and it’s soo beautiful! I can’t wait to see what other color combos Caroline comes up with.

Here’s the matching underwear – sorry it looks so unimpressive haha. I cut the XS based on my hip measurement (I was very apprehensive about this, as I normally wear a small), and the fit is pretty good. I think the butt area needs… something. Maybe I didn’t stretch the elastic enough. I feel like it makes my butt look flat, but Landon tells me I’m being ridiculous. Either way, they’re pretty comfy. I wore them all day yesterday and didn’t get a wedgie, which is awesome haha.

Since these posts are somewhat useless to me without a live model wearing the goods (if you want THAT, go holler at Heather Lou), here’s another floating bra photo for your consideration:

For a non-underwired bra, it’s surprisingly supportive! I also wore this all day yesterday (with the matching bikini, bc, duh), and it’s really really comfortable. Way more comfortable than those Bambi bras I made. And it’s REALLY cute on – I am thinking that with a couple minor tweaks to the strapping and back hook, this would make a fabulous bathing suit pattern. I just need to figure out how to stabilize that cradle – it has to stay rigid, and I think the stuff I’m using isn’t really water-friendly (and definitely wouldn’t hold up in chlorine or salt water). Any suggestions or ideas?

Also, it’s not lost on me that I would consider making a bathing suit from this pattern, but can’t bear to show my skin with the bra in this blog post. Oh well.

Bra making is SO MUCH FUN, you guys! Good thing that happens to be a hole in my wardrobe, because I really love making them and I definitely want to do more! I’m really looking forward to the Bra Making Workshop in Philly next weekend – I have sooo much to learn, and I know Maddie is going to be an amazing teacher!