Dumpster Dresser from 2x4s
Free plans to make a crate style dresser from Ana-White.com
Attach the two frames together with 2x4 boards. The drawers will run along the top of these boards.
Make SURE your face frames are direcltly in line with each other.
Project Type:Storage Dresser
Skill Level:
Advanced
Room:
Bedroom Kids and Toys
Dimensions:
Dimensions shown in diagram
Cut List:
FACE FRAMES
4 - 2x4 @ 31"
4 - 2x2 @ 43-1/2"
2 - 2x4 @ 43-1/2
4 - 2x2 @ 11-1/2"
REMAINDER OF CABINET
10 - 2x4 @ 16-1/2" (should be equal in length to the width of three 1x6s (see step 6)
8 - 1x2 @ 16-1/2" (drawer guides)
6 - 1x6 @ 29-1/2"
4 - 1x2 @ 16-1/2" (cut to fit)
2 - 1x4 @ 16-1/2" (cut to fit)
DRAWERS
6 - 1x10 @ 12-1/4"
12- 1x10 @ 17"
6 - 1/4" plywood @ 17-3/4" x 13-1/4"
6 - 1x12 @ 13-1/4"
TOP
6 - 2x4 @ 47-1/2"
2 - 2x4 @ 21"
Cutting Instructions:This plan must be altered if your boards do not measure as follows - 2x4 - 1-1/2" x 3-1/2" 1x12 - 3/4" x 11-1/4" 1x6 - 3/4" x 5-1/2"
Author Notes:
Happy Monday folks!
I'm so excited today to finally start our Blogger Feature Series!
(For those of you that have no idea what I'm talking about, you can read more about it here. And for those of you who have submitted, thank you! Please be patient, we've had an awesome but overwhelming response, and we will be taking this one week at a time. We'll be continuing the series indefinitely.)
So meet our first new blogger, Vicky from Made at this Place.
I remember when I first started building. I had fallen in love with a timber sectional at a store that at that time wasn't even in Australia, and while googling how I could get my hands on a cheaper version and one sold here I came across Ana White's blog, and there were the plans for the outdoor sectional I wanted. I managed to convince my husband that he should build it, I helped along the way of course and that was it, I was off and racing.
One of my next/first builds was the kids $4 stacking chair, a simple enough project, but to me back then, oh so daunting. I procrastinated over it for weeks and finally just had a go, and it was not as hard as I thought, sure it didn't scream craftsman’s skills but hey at that time our son was only a few years old if that, and he though it was wonderful. His excitement at my build spurred me on.
I discovered lots of blogs from ordinary people, who liked to share what they were doing. So I started mine. http://madeatthisplace.blogspot.com.au
Here are a few of Vicky's projects -
A solid wood crate dresser!!!
Here's from Vicky -
This dumpster dresser has been on my wish list for a long time, I had seen it for sale in a catalogue but the cost of the dresser plus shipping made it too expensive to justify. I could not wait to get started. It was straight forward to build. It took me a week on and off, but it is school holidays here and I have a six year old to entertain at the same time. You could probably do it in a weekend with no distractions. I used mini wax weathered oak stain, then followed with a cedar stain. I think the cedar warmed it up a bit.
The cost came in at just under $300 Australian dollars which included the finish. That’s about $260 US I think.
The dresser is now in our sons room, it is the perfect height for him and the big drawers give him quick and easy access.
You can check out more photos, including finishing steps and construction photos here.
You can go check out more projects on Made at this Place here.
Thank you so much Vicky for collaborating!
Plans for the dresser follow - enjoy!
XO Ana
Build the face frames for front and back. It is very important that the face frames be identical to keep the drawers from sliding cockeyed.
TIP: You may wish to drill 1-1/2" pocket holes facing up on the inside of the project for attaching the top in later steps.
Add 1x2s on top of 2x4s to guide the drawers as they slide. Make sure the 1x2s are square to the front face frame. Screw these down with just 2 screws so they can be easily adjusted if needed.
Test the fit of the drawers in the frame. Adjust as needed.
TIP: Vicky also recommends adding a small block at the back of the drawers to keep the drawers from pushing in too far.
Build the drawer boxes to fit - 1/4" less in width and height than the openings to allow an 1/8" gap on all sides of the drawer.
Once you are happy with the drawers, attach 1x6s to side panels.
Trim side panels with 1x2s and 1x4s to keep the look consistent.
Build top seperately with pocket holes and attach to top.
Add 1/4" plywood to back if desired.
Preparation Instructions:Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Shopping List:
8 - 2x4 @ 8 feet long
3 - 2x2 @ 8 feet long
3 - 1x2 @ 8 feet long
1 - 1x4 @ 3 feet long
2 - 1x6 @ 8 feet long
24 feet of 1x10 boards or other boards for drawer boxes
1 - 1x12 @ 8 feet long
Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!
Tools:measuring tape square pencil safety glasses hearing protection Kreg Jig™ drill compound miter saw nailer sander
